Friday 31 May 2019

Redoubt No. 1

In the last post (link below), I highlighted some rubberised wooden wall planking, picked up on a recent visit to a model rail shop, which instantly looked like it would be useful in lining the inner wall of a redoubt or trench and now, the deed has been done! ...... Redoubt No.1 is ready for action.



While at the hobby shop, I saw a single length of balsa wood, which was unusually cut, in what I can only only loosely describe as a ‘D’ shaped moulding. It gives a great starting form to get a revetment going, providing a flat edge for gluing to the base, a flat edge for the interior wall and a bevel for the the embankment, though I suppose, the more easily available quarter bead in softwood would work similarly well. A plastic base, some coffee stirrers and some filler and the build project was ready to go.



I commonly use 50mm wide bases for 28mm gunpowder era units, so the interior was given a width of 110mm, which allows two artillery or two infantry bases to sit within it, side-by-side. The outer length of the two arms were also cut at 110mm and angled out slightly.


The floor has wooden planking twin gun platforms, made from coffee stirrers, cut to 50mm lengths. It would be best (next time!) to leave a gap between the stirrers and the front interior wall, so that the wooden planking for the wall can have room to fully drop down into place, to make it easier to look like it goes below ground level. The base is shaped from ever useful plasticard.



Once the basic structure is in place, dressing it is pretty straight forward. I used Ronseal wood filler for joints and rough basing, which is conveniently coloured brown, artists acrylic modelling paste to both basecoat and seal the balsa wood with a low texture and then an application of light and medium sand (mixed) onto thin PVA.



Painting, dry brushing, dry brushing, dry brushing and even more dry brushing and then a very light dusting of a fine flock, completed the look.



I was looking at a recently ploughed field today, already the rich black loam is being occupied by a blanket of seedling heads popping up on the flanks of the furrows, which I assume has nothing to do with the potato crop itself, so I reasoned that our earthworks, even if recently built, would also likely be quickly populated by a variety of hopeful green shoots poking out.



I was surprised that I didn’t need to put a 'mucky' wash over the work, probably because the Raw Umber undercoat was hard to kill with the dry brushing and so inking wasn’t necessary. A quick blast of mat varnish was used to give a final seal. The rubber planking looks the part (website in the Resource Section below) and has not had any inks or paint applied to it, except on the exposed top, where it was cut from the sheet. It is available in other sizes, so similar pieces can be scaled according to need.



All-in-all, it looks rather good, even if I say so myself and is a piece that should prove useful across several periods.


Resources;
The rubberised wall planking has a web address on the packaging and is available in three sizes / scales. LINK
http://www.choochenterprises.com


The previous post shows the rubberised wall in its sheet form LINK


25 comments:

  1. Lovely job Norm. Glad to see someone else is a coffee stirrer user!

    ReplyDelete
    Replies
    1. They are slowly making several appearances :-)

      Delete
  2. Replies
    1. Thank you, I think you have to be in the mood for terrain making and this was enjoyable.

      Delete
  3. Great use of "bits n pieces" in the true spirit of wargaming DIY Norm - seems like a simple process to make but the result is outstanding!

    ReplyDelete
    Replies
    1. Thanks so much .. there are enough bits left for Redoubt No. 2 :-)

      Delete
  4. Replies
    1. Thanks Jonathan, I could get the bug for this sort of thing :-)

      Delete
    2. Great! I could use a few in 10mm!

      Delete
  5. Creative and wonderful work, looks superb!

    ReplyDelete
    Replies
    1. Thanks Phil, now I need a redoubt scenario!

      Delete
  6. Your scratch building efforts have produced a very effective looking redoubt.

    ReplyDelete
    Replies
    1. Thanks Peter, I can see the satisfaction that can be had out of this sort of thing and the likes of your fort etc.

      Delete
  7. Very cool piece of works. Looks splendid.
    Now you’ll probably need to make more. 😀

    ReplyDelete
  8. Funny you say that .. it just so happens .... :-)

    ReplyDelete
  9. Made a mental note of the coffee stirrers Norm, great for planking etc as you illustrate. Lovely piece, and the groundwork is most convincingly finished.

    ReplyDelete
  10. Thanks Lee, one of the few times that the thing envisioned in my head actually translates across to the completed item!

    ReplyDelete
  11. Lovely work Norm. I am about to start work on a fortification of my own and really like the broken earth effect you have achieved.

    ReplyDelete
    Replies
    1. Thanks Mark, I think the fineness of the sand is an important part of that.

      Delete
  12. Hmmm, Borodino refight next? I wonder......

    ReplyDelete
    Replies
    1. Mike, from memory the Borodino redoubts would give a good point of reference to doing different sized redoubts, a sort of small set. I would like to collect a Russian army.

      Delete
  13. I always love seeing the construction stage, as it often gives me ideas. The finished article is great.

    I'm pretty sure I read that ECW redoubts were faced with turf which was pegged into position, to help prevent the soil from eroding and also creating a more slippery surface for any troops assaulting. I could be mistaken though!

    ReplyDelete
  14. Thanks Steve, the turf idea makes good sense and I suppose what time of year construction happened would matter.

    ReplyDelete
  15. Lovely bit of scratch building and the rubber sheet worked a treat! The use of the balsa moulding was a really smart move and the finish is really convincing!
    Best Iain

    ReplyDelete
  16. Thanks Iain, your encouragement in the last post made me switch of the computer and actually start the project. :-)

    ReplyDelete

Thanks for taking the time to comment